INTERPLATER HD85 135 THERMAL PDF

Interplater hd85 thermal pdf. Thermal analysis and design enae d principles of space systems design u n i v e r s i t y o f maryland nonideal radiative. Service Manual + 68/85 Plate Processor InterPlater 85/ HD Polymer Service manual Plate Processor+ 68/85 .. Cleaning of developer heating element. Thermal Plate Processor Raptor 85/ Interplater HD 85 G&J used/refurbished. Glunz Jensen Interplater Plate Processor Model Perfect Condition.

Author: Doulmaran Zolojora
Country: India
Language: English (Spanish)
Genre: Love
Published (Last): 1 March 2008
Pages: 407
PDF File Size: 1.94 Mb
ePub File Size: 2.94 Mb
ISBN: 950-1-25732-647-5
Downloads: 63855
Price: Free* [*Free Regsitration Required]
Uploader: Faell

The basis of any gaseous or liquid waste incineration system is a thermal oxidizer. Design of thermal interface material with high thermal. When selecting a cable type take the following into account: Touch screen control panel MMI A graphical user interface colour display. X3,A to F10,1 Yellow: The stop-roller 6 ensures that water does not run back into the pre-heat section. To facilitate this a Preventive Maintenance Program has been developed, consisting of a number of relevant service-parts to be replaced at specific service intervals.

How to read pdf files in my mobile

Do not let is slip down behind the rear panel. The exit table is mounted from the factory and prepared for slanted position A.

The processor will initialize and then automatically switch to Ready mode. Temperatures 68 85 Developer min. Also be aware that the processor’s heaters and motors will be in operation during the initial startup if you hx85 overridden the machine’s safety functions. Install the rollers 7 from the pre-heat section.

Glunz Jensen

See the description for stacker connecting above. If the processor has low level by starting up, or goes low level during production, pump will be activated from Manual mode in the Tool box. Thermal analysis and design enae d 153 of space systems design u n i v e r s i t y o f maryland nonideal ud85 equilibrium temp assume a spherical body of radius r heat in due to intercepted solar flux heat out due to radiation from total surface area.

  CALCULO PURCELL 9NA EDICION LIBRO SOLUCIONARIO PDF

Thorough cleaning of the processor tank interior, tank parts, pumps, filters etc. Software user settings A few adjustments of user program parameters are also needed before the installation is finished.

If main power has been cut off temporarily the processor switches to off mode green led flashes. For cleaning and maintenance subjects see the processor user manual. Standard ibterplater hours for on-line machine: Please note that where this label appears on the processor, electrical shock hazard still exists when the main switch is turned off.

InterPlater 85/ HD Thermal | Glunz & Jensen

The processor is operated on the touch screen display. Occasionally, depending on the local water quality, it may be necessary hd855 use a drill bit to clean the holes and remove sediments mechanically. Repeat 2 and 3 for the gear end of the brush roller. Always read the Safety Instruction Manual part No before installing or operating the equipment.

This is done when installation of the processor has been completed. If this does not help, take the pump apart and clean both of the small valves in warm water. When installation of the setter interface is complete please return to this manual for finishing the entire installation by continueing with the instructions on the next page.

It must therefore be connected to earth to avoid electrical hd885. Some of the printer parts are listed in the cross reference list later in this manual. G 0-A mbe urs Ho Nu. The troubleshooting guide is divided into two sections: CE Declaration of Conformity 4 Language: Make sure that the test plate 4 is entered at right angles 4a to the rollers.

  COMPILADORES PRINCIPIOS TECNICAS E FERRAMENTAS PDF

Level out the processor crosswise by placing the spirit level on the guide 6 at the entrance of the dryer section.

InterPlater 85/ HD Service Manual |

Provide for additional cable protection, e. When performing any service, maintenance, calibration, or trouble shooting etc. For more information about the cooling unit please consult the cooler unit manual. The plate is transported through the processor by a series of rollers and roller guides. X3,A to F10,5 Yellow: The processor measures the plate size to determine the correct amount of replenisher for each plate.

Developer The processor is equipped with a fill-up pump for developer. Lead the cable as shown below. T y che ort rol cle 1. Incorrect storage may very well result in unsatisfactory processing quality etc. H8d5 ensure that the new fuse is of the correct rating according to the tbermal. Cleaning of spray tubes Developer section Clean the spray tubes in tnermal developer section with hot water to remove potential blocking of the holes. Alternatively a forklift truck is recommended.

Install the rollers as shown on the label. All disposal of parts from the machine must be made according thermak local regulations with special regards to following parts: No wash water recirculation.

X3,F to F10,1 Black: For personal protection Lint-free cloth, sponge and soft brush.