ASTM A463 PDF

ASTM A – Designation: A /A M – 02a Standard Speci?cation for Steel Sheet, Aluminum-. Find the most up-to-date version of ASTM A at Engineering ASTM A/AM: Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process.

Author: Mikakree Zolozilkree
Country: Paraguay
Language: English (Spanish)
Genre: Finance
Published (Last): 23 April 2007
Pages: 143
PDF File Size: 3.7 Mb
ePub File Size: 6.51 Mb
ISBN: 311-7-68847-383-2
Downloads: 88276
Price: Free* [*Free Regsitration Required]
Uploader: Zulkikazahn

The purchaser shall specify the appropriate table of thickness tolerances in Speci? Within the text, SI units are shown in brackets. Originally published as A — 62 T. B These typical mechanical properties apply to the full range of steel sheet thicknesses. Continuing dialogue between users and producers will have to be maintained to assist in the transition to the new designation system.

Values outside of these ranges are to be expected. There are many interrelated factors that affect the ability of asstm steel to cold form over a given radius under shop conditions. We also ask that you refer to MatWeb’s terms of use regarding this information. Please read our License Agreement regarding materials data and our Privacy Policy.

ASTM A463 Grade FSS-439

atm To see MatWeb’s complete data sheet for this material including material property data, metal compositions, material suppliers, etcplease click the button below. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Those who use these documents must determine which speci? J Shall contain silicon 1. NOTE 1—Typical ordering descriptions are as follows: Within the text, SI units are shown in brackets. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  CEDRIC PRICE POTTERIES THINKBELT PDF

C When a deoxidized steel is required for the application, the purchaser has the option to order CS and FS to a minimum of 0.

Login to see your most recently viewed materials here. Because of the many variables and changing conditions that are characteristic of continuous hot-dip coating lines, the weight [mass] of coating is not always sstm divided between the two surfaces of a sheet, nor is the coating evenly distributed from edge to edge. Dimensions and Permissible Variations 9.

These steel characteristics are important to users concerned with the weldability and formability of the coated steel products. E No typical mechanical properties have been established. The contents, results, and technical data from this site may not be reproduced either electronically, photographically or substantively without permission from MatWeb, LLC. We advise that you only use the original value or one a436 its raw conversions in your calculations to minimize rounding error. This is not considered to be a fault of the steel but is rather a function of the induced cold-work.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. The former designations also did not re? Link to Active This link will always route to the current Active version of the standard. H Shall be furnished as a stabilized steel.

  CREONTIADES PALLIDUS PDF

ASTM A Aluminum-Coated Steel, Type I, Drawing Quality

MatWeb is intended for personal, non-commercial use. Coating weight and bend tests shall be made to conform to the requirements specified.

These mechanical property values are nonmandatory. All other values in Table X2. Historical Version s – a4633 previous versions of standard. C a43 ranges are to be expected. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

The yield strength tends to increase and some of the formability values tend to decrease as the sheet thickness decreases. This specification covers aluminum-coated steel sheet in coils and cut lengths available with two types of aluminum coating applied by the hot-dip process, with several coating weights.

Flaking of the coating a4633 0. I Shall contain silicon 1. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

D If a higher tensile strength is required, the user should consult the producer. Questions or comments about MatWeb? B Weight [mass] to thickness conversions are reliable to only two signi?

Each system shall be used independently of the other.