Every precaution has been taken in the preparation of this manual. Never- . 3G3JV,AB to 3G3JV,AB ( to kW) Single,phase ,VAC. Input. View and Download OMRON 3G3JV manual online. Simple Speed Control Compact Inverters with Easy-to-use Functions. 3G3JV Inverter pdf manual download. Manuals and User Guides for OMRON SYSDRIVE 3G3JV. We have 4 OMRON SYSDRIVE 3G3JV manuals available for free PDF download: User Manual.
|Published (Last):||8 March 2004|
|PDF File Size:||18.14 Mb|
|ePub File Size:||19.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
The braking resistor cannot be connected because no braking transistor is incorporated.
OMRON 3G3JV MANUAL Pdf Download.
Drive Mode And Program Mode Chapter 7 Communications Register Number Allocations in Detail The following description provides information on register numbers allocated to the Inverter and the meanings of the registers.
Cable length 50 m or less m or less More than m Carrier frequency 10 kHz max. Monitors the completion of the data sent. Chapter 7 Communications Message The label name of the response.
Omron SYSDRIVE 3G3JV User Manual
The motor will burn out if it manuxl continuously at the rated torque in an environment in which the maximum ambient operating temperature is exceeded. Motor Rated Slip Changes during operation Enter text from picture: The monitor number display will appear again by pressing the Mode Key. Page 13 Inching frequency com- mand Note: There are two models of Adapter Panel available. Actual Load Operation Used to set the inching frequency command.
OMRON SYSDRIVE 3G3JV Manuals
Communications With Programmable Controller About this Manual This manual is divided into the chapters described in the following table. Slip Compensation Function H Countermeasures against Harmonics With the continuing development of electronics, the generation of harmonics from indus- trial machines has been causing problems recently.
An incorrect power supply may result in fire, injury, or malfunction. Because the power factor of the input power supply changes, the power factor will improve if an AC reactor is inserted. Chapter 7 Communications Message Name The label name of the sequence. Warning Labels Warning labels manuql pasted on the product as shown in the following illustration.
Select and set one out of two frequency references in n Conforming To Ec Directive Page 55 Chapter 2 Design D Grounding the Shield In order to ground the shield securely, it is recommended that a cable mankal be directly connected to the ground plate as shown below. Main Circuit Terminals Use the Increment or Decrement Key to set the frequency reference.
Preparing For Operation And Monitoring If the Inverter has a communications failure, take the steps provided below to check whether the communications function of the Inverter is normal.
Synchronous Motor Chapter 11 Using the Inverter for a Motor D Noise Noise is almost the same as when the motor is operated with a commercial power supply. Frequency Reference Input Selection n03 Refer to this chapter to use the various advanced functions, such as stall prevention, carrier frequency setting, overtorque detection, torque compensation, and slip com- pensation. Digital Operator Case Fault Retry n48 Each DSR message or response is divided into 8-bit blocks.
Milner Avenue Toronto, Ontario M The Inverter does not retrieve or pro- cess this data. Please read this manual thoroughly and handle and operate the product with care.
The inching frequency command takes precedence over the multi-step speed reference i. Should you find any problems with the product, immediately contact your nearest local sales representative.
Page Communications Chapter 7 Set data: Installation Precautions Transportation Precautions Caution Do not hold by front cover or panelinstead, hold by the radiation fin heat sink while transporting the product. Page Note In the above communications, the default is —1 and the LSB least-significant byte is converted as MSB most-significant byte in the opposite direction. Chapter 7 Communications Note It is recommended that the number be set to 3 or larger.
Chapter 6 Advanced Operation Slip Maual Function The slip compensation function calculates the motor torque according to the output cur- rent, and sets gain to compensate for output frequency. In addition, cooling effects also decline the low-speed range, resulting in an increase in the motor 3g3jb perature.
To cancel the set value, press the Mode Key instead. 3f3jv Detection nonfatal Error Chapter 8 Maintenance Operations Warning Detection Nonfatal Error The warning detection is a mannual of Inverter protective function that does not operate the fault contact output and returns the Inverter to its original status once the cause of the error has been removed.
Omron shall not be liable for any delay or failure in delivery S When there are no difficulties using the no-load operation, connect the mechanical system to the motor and operate using the Digital Operator. General ,anual Make sure that these protective covers are on the product before use. The settings of parameters described here will be sufficient for simple Inverter opera- tions.
Inspection And Maintenance